Why Batteries Discharge More Quickly in Cold Weather

If you live in a place that gets a cold winter, you know to keep jumper cables in your car because theres a good chance you or someone you know will have a dead battery. If you use your phone or camera in really cold weather, its battery life drops, too. Why do batteries discharge more quickly in cold weather? Key Takeaways: Why Batteries Lose Charge When It's Cold How long batteries hold their charge and how quickly they discharge when used depends on battery design and temperature.Cool batteries hold a charge longer than warm batteries. Cold batteries discharge faster than hot batteries.Most batteries can be damaged by excessive temperature and may ignite or explode if its too hot.Refrigerating charged batteries may help them hold their charge, but its best to use the batteries near room temperature to ensure they last as long as possible. The Effect of Temperature on Batteries The electric current generated by a battery is produced when a connection is made between its positive and negative terminals. When the terminals are connected, a chemical reaction is initiated that generates electrons to supply the current of the battery. Lowering the ambient temperature causes chemical reactions to proceed more slowly, so a battery used at a low temperature produces less current than at a higher temperature. As cold batteries run down they quickly reach the point where they cannot deliver enough current to keep up with the demand. If the battery is warmed up again it will operate normally. One solution to this problem is to make certain batteries are warm just prior to use. Preheating batteries is not unusual for certain situations. Automotive batteries are protected somewhat if a vehicle is in a garage, although trickle chargers (aka battery maintainers) may be needed if the temperature is very low. If the battery is already warm and insulated, it may make sense to use the batterys own power to operate a heating coil. Keep smaller batteries in a pocket. It is reasonable to have batteries warm for use, but the discharge curve for most batteries is more dependent on battery design and chemistry than on temperature. This means that if the current drawn by the equipment is low in relation to the power rating of the cell, then the effect of temperature may be negligible. On the other hand, when a battery is not in use, it will slowly lose its charge as a result of leakage between the terminals. This chemical reaction is also temperature-dependent, so unused batteries will lose their charge more slowly at cooler temperatures than at warmer temperatures. For example, certain rechargeable batteries may go flat in approximately two weeks at normal room temperature but may last more than twice as long if refrigerated. Bottom Line on the Effect of Temperature on Batteries Cold batteries hold their charge longer than room temperature batteries; hot batteries dont hold a charge as well as room temperature or cold batteries. Its good practice to store unused batteries in a cool location.Cold batteries discharge faster than warmer batteries, so if youre using a cold battery, keep a warm one in reserve. If batteries are small, keeping them in a jacket pocket is usually good enough.Some types of batteries are adversely affected by high temperatures. A runaway effect can occur, potentially leading to a fire or explosion. This is commonly seen in lithium batteries, such as you might find in a laptop or cell phone.

Childhood Obesity The Overbearing Truth - 1664 Words

Jayden Sadettan Schlesinger English 131 November 22nd 2015 Childhood Obesity; the Overbearing Truth. â€Å"Childhood obesity is best tackled at home through improved parental involvement, increased physical exercise, better diet and restraint from eating† – Bob Filner Imagine growing up in a household where one can eat anything. Whether an unlimited amount of sweets or entrees. This is happening now. Parents are unaware of their children eating and physical habits. Leading to the whopping amount of $190 billion in medical bills. This is all because of obesity related problems in The United States (Phit). One out of three children are considered overweight or obese between the ages of 2-19 (Gavin). Childhood obesity is ruthless. It leads to an†¦show more content†¦Parents need to be ambitious for their kids. Parents need to be consumed in helping their kids in order for them to live a healthy lifestyle. By realizing they are the ones distributing the nutrients to their children. They will have a self-realization that the kids aren’t the ones making the bad decisions. Parents will then realize that they are the ones who are in charge of their child’s urgency for a healthier lifestyle. They will realize the media influences an d the increased of childhood obesity over the past 25 years. All across the world, society is infused with media. Everything is about it. Movies, news celebrities, and the worst one. Advertisements. These ads cause the human to long for the need to obtain a certain product. The greatest victim is the children. Watching television everyday can make the children ache for the need to own the new toy or something, junk food. Junk food is advertised as good food or â€Å"hip† food. Kids become persuaded with the images and videos into thinking that they must want it, thus asking their parents. A study done by Dr. Strasburger figured out that screen time that advertises junk food and fast food increases children s requests for those particular foods and products. Such as; snacking increases while watching TV or movies, and late-night screen time interferes with getting adequate amounts of sleep, which is a known risk factor for obesity (Strasburger). This includes the studies that were conducted by the nations

Computer Drawing Free Essays

Chapter 1 1. Explain the difference between engineers and technologists. Engineers are problem solvers. We will write a custom essay sample on Computer Drawing or any similar topic only for you Order Now They are creative to use technical means to solve problems. They design products, systems, devices, and structures to improve our living conditions. They work with engineers and are concerned with the practical aspects of engineering in planning and production. 2. How can visualizing help an engineer in the design process? Visualization can help an engineer to mentally picture things that do not exist. Besides, engineers with good visualization ability are able to picture things in their minds. Furthermore, good visualization skills allow them to control mental image, allowing them to move around the image, change the form, look inside, and picture the inside of the mental image of the design problem. 3. What are the three main areas or phases of the model-centered design process? Do the activities in these areas happen in a sequential fashion? The three main areas of phases of the model-centered design process are ideation, refinement, and implementation. Windows 7 Check Your Understanding iframe class="wp-embedded-content" sandbox="allow-scripts" security="restricted" style="position: absolute; clip: rect(1px, 1px, 1px, 1px);" src="https://phdessay.com/windows-7-check-your-understanding/embed/#?secret=5NF5NpjJNR" data-secret="5NF5NpjJNR" width="500" height="282" title="#8220;Windows 7 Check Your Understanding#8221; #8212; Free Essays - PhDessay.com" frameborder="0" marginwidth="0" marginheight="0" scrolling="no"/iframe Model-centered engineering design is a nonlinear team approach to design that brings together the input, processes, and output elements necessary to produce a product. 4. Explain how PLM is used in the design process. What is its relationship to CIC? Product Life Cycle Management (PLM) is an organizational model that involves all the company’s department, including the engineering design process, in the design and manufacture of a product. In addition to CAD software, specialized software products and technologies are used in conjunction. PLM is used as a basis for creating the accumulated corporate intellectual capital (CIC) of a company or organization. 5. Outline the steps of problem identification in the ideation phase. Problem identification is an ideation process which consisting six elements: Problem statement, Research, Data gathering, Objectives, Limitations, and Scheduling. 6. What kinds of graphics are used in the ideation phase? The types of graphics used in ideation phase include charts, graphs, ideation sketches and drawings, design drawings, analysis and concept models, and presentation graphics. 7. What is the designer’s notebook? How is it used? A designer’s notebook is similar to a diary and contains many notes and sketches that are organized to show the path of development for a product and process. A well documented notebook contains notes, calculations, signatures, and dates. Keeping good note can make an accurate document for an original design. 8. Outline the main activities in the refinement phase. Refinement is a repetitive (iterative or cyclical) process used to test a preliminary design. Refinement consists of three main areas: modeling, design analysis, and design visualization. . Describe the different kinds of models used in the design process. Modeling is the process of representing abstract ideas, words, and forms, through the orderly use of simplified text and images. Models are classified as either descriptive or predictive. Descriptive model presents abstract ideas, products, or processes in a recognize form. Descriptive models consisting 3-D CA D or physical scale models used simply to visually represent the design. Predictive models can be mathematical or virtual 3-D CAD models that can be used to analyze the motion or physical properties of the design. 0. Describe the different kinds of analysis techniques used in the design process. Types of analysis techniques used in the design process are Property analysis, Mechanism analysis, Functional analysis, Human factors analysis, Aesthetic analysis, Market analysis, and Financial analysis. 11. Outline the three ways the 3-D model database can be used in the implementation phase. Three ways the 3-D model database can be used in the implementation phase are production, marketing and service documentation. Production is 3-D CAD models which are used to run machine tools and make parts and layout the factory floor. Marketing is 3-D CAD models are used for illustrations, presentation graphics, and advertising. Service Documentation is 3-D CAD models are used for service manuals, training, and assembly instructions. 12. What kinds of documentation might be produced as part of the design process? Design process documentation 2-D engineering drawings, 3-D design models, presentation drawings and illustrations. 13. Explain the role of PDM in the design process. What is the relationship of ERP to PDM? Product Data Management (PDM) is the name given to specific computer-based tools and used to track CAD or office documents with user-defined data fields, such as revisions, authors, date, and so forth in the development and manufacture of a product. Within PDM, Enterprise resource planning (ERP) is a system that specifically focuses on the ordering of material and planning for the materials used for manufacture of a product. 14. What is the difference between conventions and standards? Conventions commonly are accepted practices, rules, or methods. In technical drawing, an example of a convention is the use of dashed lines or hidden features, on a multiview drawing to designate a feature hidden from the current viewpoint. Standards are sets of rules (formal; ANSI or ISO) that govern how technical drawings are represented. 15. Describe two reverse engineering techniques. One of the reverse engineering techniques are the using of coordinate measuring machine (CMM) that can measure objects accurately and then inputs the 3-D data into a CAD system and modified it. Another one is called scanning by using laser or specialized photographic equipment to make critical measurement from existing parts. 16. Describe two different rapid prototyping technologies. One of the rapid prototyping technologies are Stereolithography (SLA) which using a laser focused beam to harden a light-sensitive polymer. Another one is Fused Deposition Modeling (FDM) which using a molten plastic to deposit a series of very thin layers to build and create a part. 17. Explain why an enterprise might want to store data in an off-site data warehouse. Then reason of an enterprise want to store data in an off-site data warehouse is protect against fire or other castasthophies at the companies engineering center. 18. Describe two different VR display techniques. Two different VR display are the using of head-mounted display (HMD) that only for individual users and multiple projection systems called computer augementedd virtual environments (CAVEs) for multiple users in a larger physical space. How to cite Computer Drawing, Papers Computer Drawing Free Essays Chapter 1 1. Explain the difference between engineers and technologists. Engineers are problem solvers. We will write a custom essay sample on Computer Drawing or any similar topic only for you Order Now They are creative to use technical means to solve problems. They design products, systems, devices, and structures to improve our living conditions. They work with engineers and are concerned with the practical aspects of engineering in planning and production. 2. How can visualizing help an engineer in the design process? Visualization can help an engineer to mentally picture things that do not exist. Besides, engineers with good visualization ability are able to picture things in their minds. Furthermore, good visualization skills allow them to control mental image, allowing them to move around the image, change the form, look inside, and picture the inside of the mental image of the design problem. 3. What are the three main areas or phases of the model-centered design process? Do the activities in these areas happen in a sequential fashion? The three main areas of phases of the model-centered design process are ideation, refinement, and implementation. Model-centered engineering design is a nonlinear team approach to design that brings together the input, processes, and output elements necessary to produce a product. 4. Explain how PLM is used in the design process. What is its relationship to CIC? Product Life Cycle Management (PLM) is an organizational model that involves all the company’s department, including the engineering design process, in the design and manufacture of a product. In addition to CAD software, specialized software products and technologies are used in conjunction. PLM is used as a basis for creating the accumulated corporate intellectual capital (CIC) of a company or organization. 5. Outline the steps of problem identification in the ideation phase. Problem identification is an ideation process which consisting six elements: Problem statement, Research, Data gathering, Objectives, Limitations, and Scheduling. 6. What kinds of graphics are used in the ideation phase? The types of graphics used in ideation phase include charts, graphs, ideation sketches and drawings, design drawings, analysis and concept models, and presentation graphics. 7. What is the designer’s notebook? How is it used? A designer’s notebook is similar to a diary and contains many notes and sketches that are organized to show the path of development for a product and process. A well documented notebook contains notes, calculations, signatures, and dates. Keeping good note can make an accurate document for an original design. 8. Outline the main activities in the refinement phase. Refinement is a repetitive (iterative or cyclical) process used to test a preliminary design. Refinement consists of three main areas: modeling, design analysis, and design visualization. . Describe the different kinds of models used in the design process. Modeling is the process of representing abstract ideas, words, and forms, through the orderly use of simplified text and images. Models are classified as either descriptive or predictive. Descriptive model presents abstract ideas, products, or processes in a recognize form. Descriptive models consisting 3-D CA D or physical scale models used simply to visually represent the design. Predictive models can be mathematical or virtual 3-D CAD models that can be used to analyze the motion or physical properties of the design. 0. Describe the different kinds of analysis techniques used in the design process. Types of analysis techniques used in the design process are Property analysis, Mechanism analysis, Functional analysis, Human factors analysis, Aesthetic analysis, Market analysis, and Financial analysis. 11. Outline the three ways the 3-D model database can be used in the implementation phase. Three ways the 3-D model database can be used in the implementation phase are production, marketing and service documentation. Production is 3-D CAD models which are used to run machine tools and make parts and layout the factory floor. Marketing is 3-D CAD models are used for illustrations, presentation graphics, and advertising. Service Documentation is 3-D CAD models are used for service manuals, training, and assembly instructions. 12. What kinds of documentation might be produced as part of the design process? Design process documentation 2-D engineering drawings, 3-D design models, presentation drawings and illustrations. 13. Explain the role of PDM in the design process. What is the relationship of ERP to PDM? Product Data Management (PDM) is the name given to specific computer-based tools and used to track CAD or office documents with user-defined data fields, such as revisions, authors, date, and so forth in the development and manufacture of a product. Within PDM, Enterprise resource planning (ERP) is a system that specifically focuses on the ordering of material and planning for the materials used for manufacture of a product. 14. What is the difference between conventions and standards? Conventions commonly are accepted practices, rules, or methods. In technical drawing, an example of a convention is the use of dashed lines or hidden features, on a multiview drawing to designate a feature hidden from the current viewpoint. Standards are sets of rules (formal; ANSI or ISO) that govern how technical drawings are represented. 15. Describe two reverse engineering techniques. One of the reverse engineering techniques are the using of coordinate measuring machine (CMM) that can measure objects accurately and then inputs the 3-D data into a CAD system and modified it. Another one is called scanning by using laser or specialized photographic equipment to make critical measurement from existing parts. 16. Describe two different rapid prototyping technologies. One of the rapid prototyping technologies are Stereolithography (SLA) which using a laser focused beam to harden a light-sensitive polymer. Another one is Fused Deposition Modeling (FDM) which using a molten plastic to deposit a series of very thin layers to build and create a part. 17. Explain why an enterprise might want to store data in an off-site data warehouse. Then reason of an enterprise want to store data in an off-site data warehouse is protect against fire or other castasthophies at the companies engineering center. 18. Describe two different VR display techniques. Two different VR display are the using of head-mounted display (HMD) that only for individual users and multiple projection systems called computer augementedd virtual environments (CAVEs) for multiple users in a larger physical space. How to cite Computer Drawing, Essay examples

Business Law for Key Performance Indicator- myassignmenthelp.com

Question: Discuss about theBusiness Law for Key Performance Indicator. Answer: As provided in the given case study it can be stated that the hotel owners have decided to renovate and extend the bistro. By virtue of being the purchasing manager of the hotel, I have been granted the authority to negotiate contracts with the suppliers to the value of $150,000 dollars. Therefore in the event of negotiating contracts with the suppliers which are more that 150,000 dollars in value, it is essential to get the approval of the directors, managers and the owners of the company. It is essential to maintain good relations with suppliers as suppliers not only provide goods and services, they are instrumental in running the business. Inspecting whether the suppliers are given payments timely is essential to maintain good relations with the suppliers. Pay records of the suppliers an be reviewed. Monitoring the financial position of the suppliers can also be helpful for maintaining a good relationship with the suppliers. Proper records of the defective goods supplied by the suppliers must be kept and inspected so as to address such issues with the suppliers. In this contract the important contract terms are that the contract would complete the construction work in time and that the contractor would paid the amount that is mentioned in the contract upon the completion of the construction work. Thus to ensure that all the contract terms are complied with, it is essential to ensure that the contractor would be paid in time and the specified amount as mentioned in the contract. However, in case of delay penalty would be imposed upon the contractor and contract can even be rescinded. KPI can be defined as the key performance indicator. It is the measurable value that shows how effectively a company is achieving its objectives. High level of KPI may focus on the overall achievement of the organization. Targeting the number of the complaints received by the suppliers can help the business to check how it addresses such complainants and how effective is the dispute resolution process of the business. The terms of the contract must be discussed with the relevant stakeholders which include the suppliers and the managers and the owners of the hotel. A copy of the contract must be provided to the relevant stakeholders so that they can examine and evaluate the document. After inspection of the contractual document, it might be signed by the contractor and the supplier, however in case any term of the contract is found to be ambiguous, such contract can be revised and sent again for approval. It can be stated that the terms of the contract are legally binding upon the parties. However the terms of the contract can be amended if it is sought by both the parties to the contract. Such amendment to the contract must be done within the life cycle of the contract. Thus in case of any dispute regarding the payment method, the contract can be amended. For amending the contract, it is important to notify all the parties to the contract about the change in the contract terms which in this given case study include the owners, directors and the suppliers. Good relations can be maintained with the suppliers by communicating with them freely. Paying the suppliers on time and address any issue faced by them can also help contractors to build good relations with the suppliers.

5 Types of Problems with Parenthetical Punctuation

5 Types of Problems with Parenthetical Punctuation 5 Types of Problems with Parenthetical Punctuation 5 Types of Problems with Parenthetical Punctuation By Mark Nichol Introducing additional but nonessential information into a sentence complicates the reader’s task when punctuation is misused. Here are five sentences that illustrate various punctuation problems associated with creating parenthetical elements in a statement. (Note that parenthetical, here and in other posts on this site, does not refer literally to the use of the punctuation marks called parentheses; it applies to the use of any punctuation to set off any amplifying or explanatory word, phrase, or sentence, such as this phrase you are reading right now, or â€Å"here and in other posts on this site.†) 1. Nextdoor, the popular neighborhood social-networking site that people use to share neighborly news too often reflects the racial biases and prejudices of its users. When an appositive of a noun or a noun phrase- an appositive is a word or phrase equivalent in meaning to the noun- precedes or follows the noun, the description must be treated as a self-contained phrase bracketed by punctuation: â€Å"Nextdoor, the popular neighborhood social-networking site that people use to share neighborly news, too often reflects the racial biases and prejudices of its users.† 2. Six objects in the icy Kuiper Belt, or Twilight Zone at the far reaches of the solar system, appear to be influenced by an as-yet-undiscovered planet. Here, the punctuation erroneously identifies â€Å"Twilight Zone at the far reaches of the solar system† as the appositive of â€Å"Kuiper Belt,† but only â€Å"Twilight Zone† serves that function; â€Å"at the far reaches of the solar system† is merely another parenthetical phrase, which must also be set off from the rest of the sentence: â€Å"Six objects in the icy Kuiper Belt, or Twilight Zone, at the far reaches of the solar system, appear to be influenced by an as-yet-undiscovered planet.† Better yet, diminish the interruption of the alternate name of the Kuiper Belt by using actually parentheses: â€Å"Six objects in the icy Kuiper Belt (also known as the Twilight Zone), at the far reaches of the solar system, appear to be influenced by an as-yet-undiscovered planet.† (Retain both commas bracketing â€Å"at the far reaches of the solar system.†) 3. He discovered one of these six objects more than a decade ago, Sedna, a large minor planet way out there on the solar system’s frontier. This sentence’s punctuation suggests that Sedna is a parenthetical. However, the phrase following Sedna is an appositive, a type of parenthetical. To give readers a sense of relative importance, one of the two commas should be changed to another punctuation mark to erase the implication that they have the same organizational weight. The clearest solution is to use a colon in place of the first comma to set up the description of what â€Å"one of these six objects† is: â€Å"He discovered one of these six objects more than a decade ago: Sedna, a large minor planet way out there on the solar system’s frontier.† 4. Twitter’s product head Kevin Weil, media head Katie Jacobs Stanton, senior vice president of engineering Alex Roetter, and Vine head Jason Toff are all leaving the company. To associate the series of appositives in this sentence, all names should be set off with commas, but that more than doubles the number of punctuation marks, which clutters the sentence. Better yet, simply change the possessive form of the company name to its base form, so that â€Å"Twitter product head† and the subsequent equivalent titles become simple descriptive phrases, thus eliminating the need for parenthetical pairs of commas: â€Å"Twitter product head Kevin Weil, media head Katie Jacobs Stanton, senior vice president of engineering Alex Roetter, and Vine head Jason Toff are all leaving the company.† 5. Engineering- figuring out how to do something- is the motivation, while repetition- making the same type of components over and over again- slows him down. Using more than one set of dashes to bracket parenthetical comments in one sentence may confuse the reader, so use parentheses instead when two or more parallel parenthetical elements are involved: â€Å"Engineering (figuring out how to do something) is the motivation, while repetition (making the same type of components over and over again) slows him down.† Want to improve your English in five minutes a day? Get a subscription and start receiving our writing tips and exercises daily! Keep learning! Browse the Punctuation category, check our popular posts, or choose a related post below:75 Synonyms for â€Å"Angry†Among vs. Amongst10 Terms for the Common People

Blood Lab essays

Blood Lab essays To show how you determine your blood type. 1. DO NOT TOUCH ANYONE ELSES BLOOD!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! 2. When cleaning up where latex gloves. Put anything that has blood on it in the biohazard container. If anything should get blood on it wipe the blood off with a alcohol swab! 1. Gather 1 alcohol swab, 1 glass slide, 3 toothpicks, cotton balls, grease pencil, 1 band- aid, RH Typing Block, Lancets, and Anti-serums A, B, and RH. 2. Take the glass slide and with a grease pencil divide the slide into 3 sections. Label one section A, the next B, and the last one D. 3. Take the alcohol swab and rub your finger with it, then dry it with a cotton ball or let your finger air dry. Then with a lancet prick your finger. 4. Next take your finger and put a drop of blood on each of the sections on your glass slide. 5. Then take Anti-serum A and put 1 drop on the square that is labeled A. On square B put 1 drop of Anti-serum B, and on square D put 1 drop of Anti-serum RH. Then stir them using separate toothpicks for each one. 6. Then place the glass slide on the RH Typing Block for 2 minutes. 8. Clean up. Follow the safety procedures!!!!!!!!!!!!!!!!!!!!!!!!! I determined that my blood type is O negative. I am this blood type because my blood did not clot in A, B, or D. I can give blood to anybody because the blood does not contain either antigen A or B. This is why my blood type is the universal donor. I can only receive blood from blood group O. If I married a RH positive person the first baby I have will be o ...

Harvard Reflection Paper - Job Sculpting Essay Example | Topics and Well Written Essays - 500 words

Harvard Reflection Paper - Job Sculpting - Essay Example James Waldroop on the other hand, is a business school graduate with expertise in entrepreneurship and human resource management. The experience of the two authors was relevant to write on human resource management. From the publication, I learnt that every person has the power of having an employee expertise required by an organization. I learnt that like everyone else I have the urge of having the opportunity of serving in the top management of an organization. The difference is that some people have the required expertise while others lack the level of education required (Harvard Business School Press, 2008). However, this does not hinder people from having a dream. It is human nature that we want to be the chief commanding officer in any organization. Not just for the job description but for the rewards that come with it. Every human has the hope and faith that they will be successful in life. The human nature is fashioned in a manner that it is never satisfied with its current achievements. The urge of having more makes the world competitive and developing. According to Harvard Business Review (2011) all humans under an organization have the hop e that one day they will move a step from their current job description. Job sculpting revolves around human nature, and the will of individuals to succeed. The will of individuals to succeed creates the difference in the way employees are devoted to their work. When sourcing for employees, personal will to succeed should be considered as an added advantage. In an argument by Harvard Business School Press (2006) personal attributes should make the most of the requirement needed by employers. In terms of retaining employees, employers should satisfy the employee need for rewards and incentives. Rewards and incentives make employees more inclined to working and achieving an organizations goal. In any organizational setting, employees are required to be devoted to achieving the goals of the organization. It is

Necessary Elements that Teachers Should Aware for Culturally and Article

Necessary Elements that Teachers Should Aware for Culturally and Linguistically - Article Example The bilingual exceptional student’s proficient instructional approaches have created additional stress for teachers and researchers to build up and for managers to expand evaluation policies that make possible legal fulfillment, at the same time make instructional sense. In the sphere of bilingual learning the question of the best sort of services, together with cultural pluralism, diverse communities, exit-entry appraisal, and the identical wellbeing of the law, are most frequently in disagreement with intercession policies, confusing the subject of what a perfect bilingual education program should achieve. There is no precise standard available to gauge and explain the range of bilingual programs existing, nor has any visibly defined variable surfaced beside which to appraise the broad competence or usefulness of bilingual education (Amber and Dew, 1983). The asymmetrical account of learners from varied socio-cultural and linguistic environment in special education has been a relentless anxiety in the field since many years. Regardless of constant hard work by teachers and researchers to recognize causative features and build up an explanation, student enrollments in special education range from over to under-representation, relying on the disability category and the specific racial/ethnic group, social class, culture, and language of the students (Donovan & Cross, 2002). Even though investigative rates of representation can alert teachers to the reality of a crisis, the important question is that in dealing with disproportional in special education whether the right student is recognized and served. It is important to focus on professional development on efficient practices for culturally and linguistically diverse learners. Since the inadequate number of teachers available with adequate training in effective practices for culturally and linguistically diverse learners, it is important that  educators engage in professional development that can lead to culturally skilled practice.  

Prevention and Control of Diseases and Health Conditions Assignment

Prevention and Control of Diseases and Health Conditions - Assignment Example In the time of menopause, women experiences declining level of progesterone and estrogen thus having symptomatic changes for women. However, HRT can be an efficient treatment for the typical menopause symptoms. According to studies on HRT, they should that the risk: benefit ratio can rise significantly for those women with ages 60 years and above. The risk involved such as stroke, breast cancer, endometrial cancer, ovarian cancer among others complications might have been the main thing that went wrong in the clinical studies (OConnor-Fleming, & Parker, 2008). HPV is said to be the most common American’s sexually transmitted disease. Merck Pharmaceuticals having introduced a vaccine that protects against the sexually transmitted virus raises many concerns, not on the issue of risks but on the issue of ethics. In my opinion, I think the vaccine will make things worse rather than good. On the issue of ethics, the vaccine will lead to some women letting their guard down when it concerns annual gynecological exams and safe sex (McKenzie, Pinger, & Kotecki, 2012). On the issue of breast cancer, the age bracket is not relevant considering the past statistics on the range of women who have died of breast cancer. According to the Canadian National Breast Screening Study, 5% of the screenings are positive or suspicious, but the 80-93 % is false positives that cause anxiety to many, however, on public perspective, this shows that the hospitals undertaking the screening might be using tests have questionable accuracy. I believe the 5% is worth saving, considering the limited resources and screening in any age group is not justifiable (OConnor-Fleming, & Parker,

The Importance of Feasibility Analysis

The Importance of Feasibility Analysis This report analyses the importance of Feasibility Analysis to businesses when they are deciding on the viability of a proposed business venture involving the implementation or improvement of an information system. This report is split into three parts the initial part defines a feasibility analysis, the second part explains how an IT feasibility analysis should be conducted using the template of the IT Infrastructure Library (ITIL) and the last section in this report examines a completed feasibility study by Powerco, a utilities distribution Company in New Zealand. What is a feasibility analysis? As the words feasibility analysis suggests a feasibility analysis is carried out to decide on the viability of a proposed venture; basically it answers the essential question of is it a viable option and should the project be implemented. All stages of the analysis are carried out in order to answer this question. When researching it is clear that the majority of all large successful businesses conduct a feasibility study to ensure they embark on a viable project, for example Microsoft have a large research department situated in many different cities throughout the globe, this department collaborates with many institutions producing many feasibility analyses a year. When examining successful businesses such as Microsoft, I discovered they will not commit to a new project without first thoroughly assessing all of the variables and reviewing the probability of success through a feasibility study. The feasibility analysis process As a feasibility analysis is often time consuming and expensive (many companies pay consultants to perform the analysis), a preliminary study is undertaken to determine if it would be worthwhile to proceed to the feasibility analysis, within this preliminary study the evaluation of alternatives is made along with brief cost and benefit analysis. A feasibility study is usually conducted after the project managers have discussed all project ideas and every possible scenario, only if the results are positive the feasibility study begins. The content of feasibility Analysis Within a feasibility study it is necessary to discuss a number of areas including; details of the present system; what are the functions and objectives, who are the Stakeholders and the reasons to improve or replace the current system for example inconsistencies / inadequacies in functionality or performance, is there any possible solution alternatives and the advantages and disadvantages of the alternatives. Feasibility analysis can be split into four types; Operational factors; Operational feasibility is used to assess how well the information systems will work if implemented in the given environment. Define the urgency of the project If the project is implemented, will it be a success? Does management support the project? How do end users feel about the new system? People tend to resist change can this problem be overcome? Can management and end users adapt to the change? Has the proposed venture conflicted with organisational or government regulations? Schedule factors; It often takes time to build and implement an information system solution; will the project still be necessary on completion? The technology may exist, but are there the skills available to not only complete the project but complete it on schedule? Is the project deadline reasonable? Is the deadline desirable or mandatory? What are the results of failing to meet the project deadline? Technical; Technical feasibility is the measure of the practicality of specific technical information system solutions and the availability of technical resources. Often new technologies are solutions looking for a problem to solve: Is the technology for the information system solution practical? Does the necessary technology exist? Is the technology proven? Is the technology practical and reliable? Are the necessary skills available to design and implement the system? Is there the infrastructure to cope with ongoing maintenance (problems, upgrades) Economic; This is regularly the most important analysis made, it asks important questions; Is the project justified (i.e. will benefits outweigh costs)? Can the project be done, within given cost constraints? What is the minimal cost to attain a certain system? Which alternative offers the best return on investment? How much will it cost to maintain? The 12 Stages of an ITIL Feasibility Analysis ITIL is a global guidance document that provides worlds best practices for IT service management companies. ITIL guidelines are often used in feasibility studies and are broken down into twelve stages. These twelve stages are described in this next section and if necessary a brief example has been given; Introduction It is important that an introduction to the feasibility analysis is made; this introduction includes the content, the intent, the intended audience, the purpose, and organizational details of the feasibility analysis. Management Summary This stage summarises, what the other stages within the template will explain in more detail; this section provides a quick overview of the feasibility analysis and would include the following, an Introduction, Management Summary, Background of the Project, Objectives, Situation, Benefits, Problems and Risks, Technical Requirements, Options, Cost/Benefit Analysis, Financial/Budget Implications and Recommendations Background to the Project A project is proposed for a specific scenario and this step describes the reason the proposal exists. For example; current sales are at a low due to increased competition, the proposal is for a new company website, where customers are able to buy directly. Objectives The high level business purposes of the proposal, including the long-range management goals. For example, the proposed project is to increase sales by an estimated 15% per annum over the next ten years. Situation This step describes the present condition, without the service in place, including market conditions, it is necessary to highlight the need for the proposed system, and the consequences of the proposal not being authorized. Benefits In the benefits section, it is necessary to focus on the short term benefits of the proposal; this is different to the objective stage which focuses on the long term gains and the cost-benefit step which focuses primarily on the financial benefits. An example of this could be the increased customer satisfaction of the proposed website. Problems and Risks It is important to identify and assess possible problems and risks of the proposed project associated with it within the development, design, and deployment stages. This is done by doing a risk assessment on the proposed system; this will be used to identify problems in many different areas, including technologies, lack of user support, or resources. Technical Requirements Has the business the technological infrastructure for the proposed system? These requirements include knowledge of the hardware and software required, for example, does the business possess the database architecture, network structures, and hardware to sustain the website, will it be necessary to outsource? Options It is recommended in the ITIL framework that a feasibility analysis includes any alternatives to the proposal, including advantages and disadvantages and costs. An example of this could be advertising to increase sales and would show the estimated cost of this. Cost/Benefit In this step, the total cost of the project is calculated; this includes development, design, deployment, and maintenance of the new service. Costs include facilities, hardware, labor, and software. The project cost is compared to the financial benefits provided by the proposed system. What are benefits? These are examples of benefits, more accurate / timely information. Improved operation, increased flexibility of operation, increased output, error reductions, cost reductions; benefits can be placed into three different categories; Monetary; when money values can be calculated, Tangible; when benefits can be quantified, but monetary values cannot be calculated. Intangible; when neither of the others apply, this applies there is a benefit, but it cannot be quantified. There are different types of costs; Project related; development, purchasing, Installation, training costs, Operational costs; these costs are often ongoing costs and include; Maintenance on the hardware; maintenance, lease, materials Software; maintenance fees and contracts Personnel; operation, maintenance There are a number of tools used, which helps in the economic section of the feasibility analysis these are; Cost-benefit analysis (CBA); which estimates and totals up the equivalent money value of the benefits and costs of proposed projects to establish whether they are worthwhile. Payback Analysis; which is used to calculate how long it will take to pay the costs of the project Return on Investment Analysis; which compares the lifetime profitability of alternative solutions, Net Present Value Analysis: using current monetary values, profitability is determined of the proposed project, Return On Investment (ROI) compares the lifetime profitability of alternative solutions, (Lifetime benefits Lifetime costs) Lifetime costs and finally you can compare alternatives with the feasibility analysis matrix. Financial/Budget Implications Once the overall costs have been established, it is necessary to verify if the necessary funds are available, if so how? This may result in changes to the budget or priorities and reducing expenditure to accommodate the costs. Recommendations In this final step recommendations regarding the proposal are made including scheduling and budgeting Summary In summary these twelve steps that make up the ITIL is among the first activities a manager will undertake in preparation for a proposal for a new IT service, though it is important to remember these steps make a general guide and different information systems may require amendments. Examples of feasibility analysis Though the majority of businesses keep their own feasibility analysis private, research identified an interesting feasibility analysis conducted by Powerco. In this section I will briefly review this feasibility analysis in a case study due to the word restrictions on this essay and the extensiveness of the ITIL framework. Powerco has an estimated 410,000 consumers which makes it one of New Zealands largest utilities Companies. These customers expect a reliable service 24 hours a day, 7 days a week. Powerco applications are split between two platforms; Oracle RAC and Microsoft SQL Server, which has meant that the business had additional expenses of licensing, supporting, operating, and maintaining two systems. Additionally it was awkward for staff to alternate between the systems when working. As the Oracle platform of Powercos warranty cycle was approaching expiration, and the financial system was scheduled an important upgrade, it was clear to the company that it was time to reassess its options and whether it should consolidate to a single server platform or replace existing hardware. Powerco acknowledged that to consolidate the database platforms would create a more simple IT environment and would reduce the total cost of the database system significantly. The case for consolidation was simple why maintain two systems if you dont need to? explains Mr. Griffiths, Infrastructure Manager, Powerco. Powerco undertook preliminary study of the solutions and assessed the pros and c ons of Oracle versus SQL Server. This analysis pointed towards some significant advantages in choosing SQL Server over Oracle. These included reduced licensing and maintenance costs, ease of management and fewer requirements for a specialised skill set to manage and service the system. A feasibility study of migrating to SQL Server was then completed by consultants on Powercos behalf including a cost/benefit analysis, a risk assessment, analysis of the alternatives and the four factors discussed earlier in this report, this confirmed Powercos applications could be supported on SQL Server, with the remaining end of life applications being replaced with SQL Server compatible ones, the feasibility study showed that unlike other options Microsoft SQL Server, serving could be done in-house. Microsofts SQL Server was the cheapest option to license, maintain, and support, particularly because of the specialised nature of Oracle. The business would be more streamline and efficient with just the single platform. Increases security. Further Tangible and Non-tangible benefits. Due to the results of the feasibility study, Powerco changed from the two platforms to solely Microsoft SQL Server, the result of this consolidation has meant Powerco has been able to reduce costs significantly, also ensuring it was easier to maintain and manage in-house and eliminating the need for external consultants. The migration to SQL Server has cut the overall cost of ownership by $390,000 a year, also helping to streamline Powercos IT systems and have given a number of other Tangible and Non-tangible benefits. Conclusion In conclusion this report has explained what a feasibility study is and when it should be used, I have then reviewed the various stages which are recommended by the IT industry experts at the ITIL and have given an example of a successful feasibility study undertaken by Powerco. I believe to be objective this report should have explored examples of a unsuccessful feasibility study, however this was not possible due to my research not providing any suitable cases, but still the findings of this report are clear, it is advisable to do a feasibility analysis, as it is tried and tested and the vast majority of large and established companies use this method to check the viability of a proposed venture and are taking a substantial risk if a feasibility study is not carried out before embarking on new project.

An Analysis of The House on Mango Street :: House Mango Street

An Analysis of The House on Mango Street In the novel, The House on Mango Street, Sandra Cisneros describes the problems that Latino women face in a society that treats them as second class citizens. A society that is dominated by men, and a society that values women for what they look like, and not for what is on inside. In her Novel Cisneros wants us to envision the obstacles that Latino women must face everyday in order to be treated equally. In the Book women are looked upon as objects by men whether they are boyfriends, friends fathers or husbands. The girls in the novel grow up with the mentality that looks and appearance are the most important things to a woman. Cisneros also shows how Latino women are expected to be loyal to their husbands, and that a husband should have complete control of the relationship. Yet on the other hand, Cisneros describes the character Esperanza as being different. Even though she is born and raised in the same culture as the women around her, she is not happy with it, and knows that someday she will break free from its ties, because she is mentally strong and has a talent for telling stories. She comes back through her stories by showing the women that they can be independent and live their own lives. In a way this is Cinceros' way of coming back and giving back to the women in her community. The Latino women and girls in the novel are extremely concerned about their appearances, because they feel that if they aren't attractive then they won't be noticed by men, and they are raised to believe that they need a man to fulfil their life, and that they need a husband to support them, and if they don't look attractive then they are not going to be noticed, and if they are not noticed, then they think they won't end up getting married. A good example of this is Marin. When Marin talks about a real job Marin says that the best place to work is downtown, not because of the work that is there, but because "you always get to look beautiful and were nice clothes." She also tells the girls that the only thing that matters is if your skirts are short, and your eyes are pretty, so that you are noticed by guys.

East and West in Antony and Cleopatra Essay

Shakespeare used as his source for the play North’s translation of Plutarch’s ‘Lives of the Noble Grecians and Romans.’ Plutarch, along with other Greek and Roman authors, saw an opposition between the conquering West, standing for moral and political virtue, and the conquered East, representing luxury and decadence.  Do you agree that this is essentially how Shakespeare presents the opposition between East and West in ‘Antony and Cleopatra?’ ‘Rome’ and ‘Egypt’ have significance far beyond physical locations; they symbolize two oppositional value systems essential within both society and the psyche. The world of ‘Antony and Cleopatra’ is riddled with polarised opposites, such as civilisation and nature, public and private, and, perhaps most importantly, passion and honour.  The inability of the East and West to reconcile their values inevitably causes conflict, forcing Antony, the tragic protagonist, to choose between the spheres. In suicide, he transcends the limitations the world thrusts upon him; joined later by Cleopatra, who finally discovers the significance of Western values, in a triumphant death. The notion of either sphere having moral superiority to the other is moot; Shakespeare passes no concrete judgement, and no simple platitude of ‘good and evil’ could suffice to explain the complex behaviour of the principal characters.  Neither Egypt nor Rome seems to be truly virtuous, despite the moralising of the Roman characters. In Rome the traditional system of honour is rapidly being subjugated beneath Caesar’s cold quest for individual supremacy. Loyalty now belongs only to the winner, and individuals such as Lepidus and Pompey are sacrificed in the imperialistic drive of Octavius. A certain misogyny is Rome, with women denounced as ‘whores,’ and the harsh treatment that Cleopatra would have faced as a captive indicates the presence of violence in the Roman psyche. Nor is Egypt an ideal of purity. A society ‘wrinkled deep in time’, its preoccupation with emotion leads it to recklessness (such as when Cleopatra flees the Battle of Actium). Theatrical and dramatic, the lifestyle at court is extremely decadent, often approaching vulgarity. Cleopatra is cosseted by her courtiers, and encouraged towards vanity, narcissism, pettiness and self-indulgence,  The notion of a duality is more important than the probity of either force; by being opposites, ‘East’ and ‘West’ become inextricable. Without ‘East’ there would be no concept of ‘West,’ and vice versa, and this pattern is applicable to all the converses that the antithetical spheres represent. Both are equally important in the development of full humanity – the values that ‘West’ and ‘East’ represent should be in harmony within both society and the human psyche. In ‘Antony and Cleopatra’ they seem to be inherently conflicted, and the subsequent polarisation causes the demise of the lovers, which allows them to, paradoxically, conquer the hearts of a world that has tried to conquer and restrict them. The structure of the play serves to highlight the antithesis, with frequent changes between the machinations of Rome and the hyperbole of Cleopatra’s court emphasizing both the opposition of the value systems and the effect that exposure to both has upon Antony.

Free Essays on Borderline Personality Disorder

Borderline Personality disorder Borderline personality disorder (BPD) is a severe, chronic, disabling, and potentially lethal psychiatric condition. People who suffer with this disorder have extreme and long standing instability in their emotional lives, as well as in their behavior and their self-image. This is a common disorder affecting two percent of the general population. The best evidence indicates that about eleven percent of psychiatric outpatients and nineteen percent of inpatients meet diagnostic criteria for BPD (Kass, et al. 1985). A person with a borderline personality disorder often experiences a repetitive pattern of disorganization and instability in mood and close personal relationships. This can cause significant distress or impairment in friendship and in work. A person with this disorder can often be bright and intelligent, and appear warm, friendly and competent. They sometimes can maintain this appearance for a number of years until their defense structure crumbles, usually around a stressful situation like the break of a romantic relationship or the death of a parent (Corelli). There are many Symptoms of borderline personality disorder such as unstable interpersonal relationships, frequent display of temper, inappropriate anger, recurrent suicide gestures, feelings of emptiness and boredom, intolerance for bring alone and an impulsiveness in at least two of the following areas: money, substance abuse, sexual relationships, reckless driving, binge eating, and shoplifting (Yahoo Health). In greater detail someone with BPD would have an intense but stormy relationship with marked shifts of feelings and difficulties in maintaining intimate, close connections with others. The person may manipulate others and often has difficulty with trusting others. There is also emotional instability with marked and frequent shifts to an empty lonely depression or to irritability and anxiety. There may be unpredictable a... Free Essays on Borderline Personality Disorder Free Essays on Borderline Personality Disorder Borderline Personality disorder Borderline personality disorder (BPD) is a severe, chronic, disabling, and potentially lethal psychiatric condition. People who suffer with this disorder have extreme and long standing instability in their emotional lives, as well as in their behavior and their self-image. This is a common disorder affecting two percent of the general population. The best evidence indicates that about eleven percent of psychiatric outpatients and nineteen percent of inpatients meet diagnostic criteria for BPD (Kass, et al. 1985). A person with a borderline personality disorder often experiences a repetitive pattern of disorganization and instability in mood and close personal relationships. This can cause significant distress or impairment in friendship and in work. A person with this disorder can often be bright and intelligent, and appear warm, friendly and competent. They sometimes can maintain this appearance for a number of years until their defense structure crumbles, usually around a stressful situation like the break of a romantic relationship or the death of a parent (Corelli). There are many Symptoms of borderline personality disorder such as unstable interpersonal relationships, frequent display of temper, inappropriate anger, recurrent suicide gestures, feelings of emptiness and boredom, intolerance for bring alone and an impulsiveness in at least two of the following areas: money, substance abuse, sexual relationships, reckless driving, binge eating, and shoplifting (Yahoo Health). In greater detail someone with BPD would have an intense but stormy relationship with marked shifts of feelings and difficulties in maintaining intimate, close connections with others. The person may manipulate others and often has difficulty with trusting others. There is also emotional instability with marked and frequent shifts to an empty lonely depression or to irritability and anxiety. There may be unpredictable a... Free Essays on Borderline Personality Disorder â€Å"Borderline Personality Disorder is a severe, chronic, disabling, and potentially lethal psychiatric condition† (BPD Research Foundation). A person with a Borderline Personality Disorder (BPD) is characterized by having a repetitive pattern of mood instability and poor self-image. The Diagnostic and Statistical Manual (DSM-IV) defines Borderline Personality Disorder as: A pervasive pattern of instability of interpersonal relationships, self-image, and affects, and marked impulsivity beginning by early adulthood and present in a variety of contexts, as indicated by five (or more) of the following: 1. frantic efforts to avoid real or imagined abandonment. Note: Do not include suicidal or self-mutilating behavior covered in Criterion 5. 2. a pattern of unstable and intense interpersonal relationships characterized by alternating between extremes of idealization and devaluation. 3. identity disturbance: markedly and persistently unstable self-image or sense of self. 4. impulsivity in at least two areas that are potentially self-damaging (e.g., spending, sex, substance abuse, reckless driving, binge eating). Note: Do not include suicidal or self-mutilating behavior covered in Criterion 5. 5. recurrent suicidal behavior, gestures, or threats, or self-mutilating behavior 6. affective instability due to a marked reactivity of mood (e.g., intense episodic dysphoria, irritability, or anxiety usually lasting a few hours and only rarely more than a few days). 7. chronic feelings of emptiness 8. inappropriate, intense anger or difficulty controlling anger (e.g., frequent displays of temper, constant anger, recurrent physical fights) 9. transient, stress-related paranoid ideation or severe dissociative symptoms (BPD Central, Markovitz, Skodol). BPD is characterized by mood instability and poor self-image. Relationships with others are intense and stormy, very unstable and are difficult in maintaining intimate, cl...

Black Legend essays

Black Legend essays William of Orange once stated, Spain committed such horrible excesses that all the barbarities, cruelties, and tyrannies ever perpetrated before are only games in comparison to what happened to the poor Indians. This statement can be viewed in several different ways: truthful, hypocritical, harsh...the list goes on. William was correct in his statement except for the first word, Spain. Even though Spain did commit horrible offenses against the Indians, William of Orange, and the rest of the European settlers, should be included in that statement. Every settler that came over to the New World, whether they were aware of it or not, condoned the horrible excesses bestowed upon the Indians. Although several other nations were involved in the horrific crimes against the Indians, Spain may have been the worst in their treatment of the natives they encountered. The Spanish felt that servitude was a natural right, especially if you were born into so form of nobility. Dona Isabel De Guevara was a woman who was born into the position of princess. She came over to the New World only to find the men weak and the food supply scarce at best. She then wrote a letter back to the Queen asking for encomiendas, or serfs. The request was granted and Guevara received several Indians for help with the every day chores while the men were weak. The Spaniards treated everyone they encountered in the New World inferior for selfish reasons. They felt that Western Europe was the center of the world and there means of living were the civilized way. There reasoning for colonization was Gold, God, and Glory. The Pope, thousands of miles away, created the Papal Bull of 1493 that divided the world between Spain and Portugal. This bold statement shows the audacity of the Spanish towards the newly discovered Natives. Even though measures were tak ...

What are the strategic priorities for policy makers in Birmingham if Essay

What are the strategic priorities for policy makers in Birmingham if they are to generate strong economic development for the city over the next 20 years - Essay Example Birmingham is a City with an important economic and cultural framework. Because of its infrastructure and its facilities – airport, university, a research park for business and technology research – the City is considered as one of the most developed cities of the West Midlands. The City’s council initiates a wide range of activities aiming to support effectively the needs of the residents. The economic development of Birmingham is examined in this paper; emphasis is given not only on the City’s current economic performance but also on its prospects for future growth. The strategic priorities for policy makers in Birmingham in the case that the City’s economic growth over the next 20 years would be initiated are identified and evaluated. After reviewing the existing plans related to the City’s economic growth it is assumed that the achievement of a further growth – over a period of 20 years – would be achievable under the terms that collaboration and communication in regard to the relevant initiatives are improved. 2. Birmingham – requirements for growth in the next 20 years.History of the town: The history of Birmingham is quite long. In accordance with the studies published on the particular subject, the presence of human in the region goes back to the Bronze Age (Birmingham, Voice of the West Midlands, History); Anglo Saxons visited the area around 700 A.D.; ‘the Medieval and Norman occupation’ (Birmingham, Voice of the West Midlands, History) of the area ended approximately in 1086; it was then that the land-owners took the control of the region occupation’ (Birmingham, Voice of the West Midlands, History). Under the influence of the industrial revolution, the City’s population has been continuously increased, up today. During the two World Wars the City suffered major damages; many of its residents participated in the Wars – and they did not return (Birmingham, Voice of the West Midlands, History). Also the City’s industrial infrastructure suffered significant damages during the above period. The restructuring and the development of the City was highly supported by foreign immigrants – it was during the 1950s and the 1960s that the City was developed significantly becoming today a major economic and cultural center in Britain (Birmingham, Voice of the West Midlands, History). The current economic and cultural status of Birmingham is reflected in the images of the town – see graphs 1 & 2 in the Appendix section. 2.2 Phases of economic development, economic characteristics The economic growth of Birmingham through the decades can be identified in the events that characterized the City’s establishment and development – as presented in the previous section. The current economic development of Birmingham is significant – compared to the financial turbulences that cities worldwide have to face. This tre nd is reflected in the reports published regarding the economic characteristics and the rate of the City’s growth. All of these reports are encouraging regarding the City’s current economic status and, especially, regarding its potentials for further growth. Moreover, the City’s Council has increased its efforts for generating funds necessary for serving the various social and economic needs of residents. In this context, ‘the Westminster, Birmingham and Manchester councils’ (Birmingham News Room 2011) have established a commission; the commission is based in Birmingham because the particular City is ‘the largest UK city economy outside of the capital’ (Birmingham News Room 2011). The above commission aims to identify at what level it is possible for the cities across UK to become independent – in terms of funding – from the central government (Birmingham News Room 2011). Today, Birmingham is an economic center in the West Midlands,

Starting and Developing a New Venture Essay Example | Topics and Well Written Essays - 2000 words - 1

Starting and Developing a New Venture - Essay Example In the case of Haji he started Easy jet airliners after leaving Stelmar Tankers, his own shipping company by persuading Lucas to lend him ?5 million. He started Easy jet a low cost budget airline using two rented 737s and ?29 one-way fares to Glasgow. By starting Easy jet Haji was not bowing to the pressures of risk but took an imperative measure even though he had been charged earlier with counts of poor maintenance of his vessels and manslaughter. Moreover he started Easy jet by borrowing money. It is a known fact that borrowed money attracts interest and the principal money has to be paid and therefore it becomes, quite impossible to get promising returns in the first years of business. In his autobiography Richard Branson reckons that his passion in doing business is motivated by setting huge goals that are apparently unachievable, and staying focused to rise above them. This shows that Branson was aware of the risks involved in a huge venture when he set up Virgin Atlantics. Bes ides in 1993, Branson took the greatest risk by venturing into the railway business. This project was very costly and most people though he would not make it. It goes without taking that Branson and Haji took a partial path when it came to risks and only took the initiative of such ventures when they deemed them worthwhile in the long run. LOCUS OF CONTROL The locus of control is the power in the principle that one can formulate and implement things. Most entrepreneurs have a high locus but in most cases they are poor in delegating duties. They are upbeat when it comes to venturing into business. They tend to be more practical and positive about their business ventures. In 1993, Branson took what most people thought was a very risky:... Curiosity and creativity is the quintessence of entrepreneurism. New products, new solutions and new ways are the core of creativity and in general entrepreneurism. It is about willing to think of all possibilities and opening one’s mind to creative things through being inquisitive of what is going on in the globe and quite often generating a gimmick of stuff that suggests one’s ability to create new products that other people are afraid of thinking. Branson has been termed as one of the new generation of the creative world. He took products that were already in existence and made them look original. He has revolutionized the airline business by integrating it with other business ventures like the Virgin Fuels and Space tourism. Virgin Fuels was designed to respond to global warming and exploit the insistence spikes in fuel expenditures by offering a revolutionary, less costly fuel for machines and, in the near future, aircraft fuel. Branson stated that he was formerly a global skeptic and his decision was influenced by Al Gore.

Analyse the reasons for the recent UK recession and its impact on one Essay

Analyse the reasons for the recent UK recession and its impact on one particular leisure market. E.g. travel, restaurants, tourism - Essay Example Choice as a factor of growth is crucial in the growth of an economy since the economy needs consumers will and choice of products in order to relish and grow. That said, it is evident that the economy requires the input of consumers and produces who act as the driving force since they provide the necessary resources which include labour, land, physical and human capital etc. This paper will discuss the main reasons why the recent UK recession occurred and its impact in the tourism industry as a leisure market. The paper will aim at answering the why and the how questions in relation to the causes and the impacts of the 2008 – 2009 UK recession that occurred between the last quarter of 2008 and the second quarter of 2009. The paper addresses the reasons of the recession in the first section and the impacts of the recession on the tourism industry in the second section and finally a conclusion, which aim at giving a clear discussion and analysis of the first two sections. Verick and Islam (2010) argue that the 2008 – 2009 global recession (financial crisis) was largely accelerated by the global imbalances that were being experienced worldwide at that time in terms of a drop in interest rates, perceptions of risks, and the regulation of financial systems. The UK was, apparently, not left behind as it faced many financial problems including near bankruptcy of banks, a fall in its stock market, large levels of public debt, a tumbling currency and frozen money markets which were all factors that promoted a recession (Cooper, 2009). Among the leading causes of the recession was the devaluation of UK currency the Sterling Pound. The Sterling Pound during the recession had a devaluated by 25-30% from the value it once held in before the recession. This was in accordance with the basic economic theory that states that any decrease in the exchange rates of a currency will eminently aid in the

Animal Abuse Problem Essay Example for Free

Animal Abuse Problem Essay Animal abuse is a people problem. Cruelty to animals can be prevented by all costs. Educate people you see abusing their animals and always, always report suspicious activity to your local law enforcement or animal control. An abused animal can turn on a human in an instant, so children and innocent bystanders can be attacked by an animal if it feels threatened. When abused, animals are not the only ones in danger. As C.S. Lewis once said, If we cut up beasts simply because they cannot prevent us and because we are backing our own side in the struggle for existence, it is only logical to cut up imbeciles, criminals, enemies, or capitalists for the same reasons. Maybe an eye for an eye should be implemented on animal abusers. Continue reading at NowPublic.com: Animal Cruelty: Facts, Prevention, Statistics and Action | NowPublic News Coverage http://www.nowpublic.com/environment/animal-cruelty-facts-prevention-statistics-and-action-2886267.html#ixzz2L2yNrWDW As humankind has progressed, there has been an increase in governance and rules and regulations of everyday life. These governance and rules rise from general disgust over happenings and concepts all over the world. One such rapidly growing concept is animal cruelty. Animal abuse simply put is cruel unwarranted treatment of animals. Such treatment generally has a single point program to subject animals and sometimes pets to unnecessary harm and pain. One major type of animal abuse is torture. Read more at Buzzle: http://www.buzzle.com/articles/animal-cruelty-animal-abuse-facts-statistics.html It is prevalent in all areas of the society. People in rural as well as urban areas are reported for animal cruelty cases. The statistics show reported cases are just the tip of the iceberg. There are hundreds, maybe thousands of cases related to animal abuse that go unreported. People carry out violent and gruesome attacks on animals, both domestic as well as stray. The most common victims of animal abuse are: Horses Livestock Dogs Cats Birds Read more at Buzzle: http://www.buzzle.com/articles/animal-abuse-statistics.html We have heard of an old saying Dogs a mans best friend. Most of us must have read Black Beauty at least once. The lion is the king of the jungle, a fact even kids from kindergarten are aware of. There are many other instances where animals are thought of as our friends. Yet, we tend to inflict pain and torture on our friends. Animal cruelty is not an issue that is unheard of. Since time immemorial, man, the high in the food chain, has tortured those beneath him. Practically all animal species have been abused by man in some way or the other. Humans are thought to be the most intelligent of all species. Still, when we look at the animal abuse statistics, mankind is put to shame. Read more at Buzzle: http://www.buzzle.com/articles/animal-abuse-statistics.html Animal Abuse Facts and Statistics It’s really hard to write about animal abuse facts. It’s hard to do the research, read the stories, get the statistics, watch the videos, and see the pictures. But the statistics are just so disturbing that readers need to know the truth. According to the Human Society of the United States, there is no national reporting system for abuse to animals. However Pet-Abuse.com has collected statistics on animal cruelty since 2001. As of October 13, 2012 they have 19,517 cases listed on their web site. The following animal abuse stats for the U.S. are from their database: Top 5 Types of Abuse [pic] †¢ 32% neglect or abandonment †¢ 12% hoarding †¢ 11% shooting †¢ 9% fighting †¢ 7% beating Most of the above forms of violence toward animals is self-explanatory. However, hoarding may need some more explanation. This involves people who are often well intentioned but what they do is collect animals and may have hundreds of animals living in their house, barn or yard. It’s pretty much impossible to take care of this number of animals well and the cost of food and veterinary care would be sky high. Hoarding is really another form of neglect, just on a much grander scale than traditional neglect or abandonment. Most cases of abuse toward animals are directed toward dogs, cats, and horses. The statistics on dogs included non-pit bulls pit bulls. Of the cases listed on their website, 48% are alleged cases, 24% are convicted records, and 16% are open. Most abusers of animals are men between 31 and 50 years of age. While many animal cruelty cases are tracked on the web, it is believed the number of cases is much greater. A recent search of Google News found more than 10 articles regarding allegations or convictions toward animals in September in Texas alone compared to just 13 on Pet-Abuse.com for all of the United States. In other words, the data on animal abuse is even worse than what is reported on well known web sites.

Argumentative Essay About College :: Education College

Dear Ben,Hey Ben! I was talking with Sean yesterday when he told me the news, you're planning to delay college. This came as a shock to me when I heard it. By not attending college, you may get a year's rest and a chance to think your decisions through, but if you ever do decide to attend college, you will miss out on a lot of opportunities as well. I think you should consider going to college rather than driving the open road after High School.The information you've learned in High School will be more fresh in your mind now than 1 year from now. You have passed 12 years of schooling, yet now you believe it is time to rest and see other places and people for a year or more before attempting college. College adds 4 more years of intense work, yet knowledge learned within High School can make learning new material easier for you. Other people often find themselves getting sidetracked once they put off the option to attend college, that can only hinder your ability to eventually become a college graduate.College can be a fun experience if shared with friends and people of similar age. By waiting an extra year or two, you will find it more uncomfortable within your classes. The entire college experience involves parties, football games, and drinking beer with your buddies as well as an education. As you get into the entire experience and enjoy college, you will understand and appreciate what a college offers.The ideal time for college is now more than ever as you also have scholarships and your parents to help with the expensive money arrangement which is needed. Parents can be a great help in paying for your college, and may be willing to pay much more immediately after graduation from High School, than paying 2 years afterwards. Scholarships are always helpful to students, paying for a little bit of an expensive college. Argumentative Essay About College :: Education College Dear Ben,Hey Ben! I was talking with Sean yesterday when he told me the news, you're planning to delay college. This came as a shock to me when I heard it. By not attending college, you may get a year's rest and a chance to think your decisions through, but if you ever do decide to attend college, you will miss out on a lot of opportunities as well. I think you should consider going to college rather than driving the open road after High School.The information you've learned in High School will be more fresh in your mind now than 1 year from now. You have passed 12 years of schooling, yet now you believe it is time to rest and see other places and people for a year or more before attempting college. College adds 4 more years of intense work, yet knowledge learned within High School can make learning new material easier for you. Other people often find themselves getting sidetracked once they put off the option to attend college, that can only hinder your ability to eventually become a college graduate.College can be a fun experience if shared with friends and people of similar age. By waiting an extra year or two, you will find it more uncomfortable within your classes. The entire college experience involves parties, football games, and drinking beer with your buddies as well as an education. As you get into the entire experience and enjoy college, you will understand and appreciate what a college offers.The ideal time for college is now more than ever as you also have scholarships and your parents to help with the expensive money arrangement which is needed. Parents can be a great help in paying for your college, and may be willing to pay much more immediately after graduation from High School, than paying 2 years afterwards. Scholarships are always helpful to students, paying for a little bit of an expensive college.

Religion in Society Essay -- Essays Papers

Religion in Society Miriam, Deborah and Huldah all are names of prophets from the Bible; they also all happen to be women. There are even two books in the Bible about women, Esther and Ruth. Psalm 68:11 reads, "The Lord gives the command; the women who proclaim the good tidings are a great host." With all of this support for women, why are they treated as the inferior sex in the church? The article, â€Å"Women and Gender; Reading the Bible through the Eyes of Women,† states that it is â€Å"crucial that women have the same opportunities and freedom of expression as men in the Church, so that the entire community may benefit from their contribution.† However, many churches do not allow women to play a role in the services, and most do not allow there to be a woman priest or pastor. Lori Beamen points out that fact that, â€Å"Although women frequently do the same work as men, they are denied the authority that accompanies those tasks when performed by men.† Statistics even show that 69.9% of women attend church more often than once a year opposed to 58.2% of men. So how can women put in so much time and do all of this work, and still be denied authority? Even though there are instances in the Bible that support women, many people use the Bible to limit women’s roles in the church and to show women are inferior in general. Some feel that since Adam was created first, and it was Eve who was responsible for the eating of the fruit, men are superior. However, the Women and Gender article notes that â€Å"When God told Adam and Eve to be fruitful and multiply, He did not talk to Adam alone. He addressed the two of them together as two equals, to whom He gave a common task. And that is exactly what partners are: two people who are equ... ...r verse. Paul writes in Galatians 3: 28-29, â€Å"There is neither Jew nor Greek, slave nor free, male nor female, for you are all one in Christ Jesus. If you belong to Christ, then you are Abraham’s seed, and heirs according to the promise.† The role of women was enhanced by Christianity and faith in Christ transcends differences and makes all believers one in Christ. Nobody is more superior than the other and if we all remember that, the better the church will function as a whole, no matter if the teachers are male or female. Bibliography African Church Information Service (2003, December 1). â€Å"Women and Gender; Reading the Bible through the Eyes of Women.† AllAfrica, Inc. Beamen, Lori. Introduction. (2004) Sociology of Religion. Wallace, Ruth A. â€Å"The Social Construction of a New Leadership Role: Catholic Women Pastors.† Sociology of Religion, p. 136.

Martha Stewart

Martha Stewart a known celebrity and founder of Martha Stewart Living Omnimedia (a business which is built on showing others how to cost effectively manage and decorate the home), who was given a tip by Douglas Fanueil and Mr. Bacanovic, employees of the Merrill Lynch brokerage company. This tip which broke the confidentiality policy of the brokerage company led to the subsequent sale of Martha’s shares in the ImClone company during the latter company’s blackout period with the effects of causing the share price of ImClone’s share to drop and the share price of shares of the Martha Stewart Living Omnimedia to drop after the scandal broke that Martha had engaged in insider trading. Through a series of events, she, her broker and his assistant were subsequently prosecuted and sentenced. In this case study, we will be examining how the public perceived Martha Stewart’s actions and also the penalties that were imposed. We will also look at how her decisions impacted and also provided major setbacks to her business because of her insider trading scandal on the Imclone Systems Incorporated. By carrying out this research, we as a group would determine if the blame should be placed on her or not and also determine if the fines were adequate for the crime committed. 1.Did Martha Stewart commit the crime of insider trading when she sold her ImClone shares on December 27, 2001? We believe that Martha Stewart was guilty of insider trading. The justifications for our point are as follows: a) Martha Stewart was told by Mr. Faneuil (under direction from his boss who was also Ms. Stewart’s stockbroker) that the largest stockholders of ImClone (Sam Waksal and his daughter Aliza) had sold all their shares in the company on that same day, December 27th, and she immediately sold hers as well. This in itself was a breach of client confidentiality and insider information because no one knew about it but their stockbrokers. By virtue of the position Mr. Bacanovic (Mr. Faneuil’s boss) at the brokerage company of Merril Lynch he was not to mention or discuss the actions of any of his other clients. b) Even though Martha Stewart did not know about the FDA’s unfavourable report about ImClone, the sudden ‘dumping’ of the shares on the market was enough for her to speculate that there must be something wrong and that she should get her shares sold as quickly as possible in order to obtain the best possible share price or avoid a loss. Tipped with the knowledge of the Waksals actions and her intuition of imminent disaster she ordered that her shares in that company be sold as quickly as possible. c) She called Sam Waksal as soon as she received the tip-off in the hopes of obtaining the reason behind their actions. d) When investigated by criminal authorities she instructed her secretary to change the original message the secretary wrote from Mr. Bacanovic and then thought better of it and advised the secretary to revise the changes and restore the original message. She also lied repeatedly to criminal authorities on the real reason behind the sudden sale of her shares. 2.Did the U.S. Attorneys and the Securities and Exchange Commission use good judgment in the indictment of Martha Stewart? Do you believe that her indictment was based on evidence of a serious crime, or do you believe that prosecutors consciously or unconsciously had additional motives for pursuing the case? It is our belief that good judgment was exercised in indicting Martha Stewart. The indictment was based on the evidence of reasonable intent. Martha Stewart on hearing of the actions of the Waksals, and making reasonable judgments that the company was in trouble, intended that she should not make a loss on her investment in ImClone and made immediate moves and succeeded in selling her shares in the company for a profit of $228,000. If she had waited until December 28th when the share price fell to $45.39 per share she would have made only $178, 292, a loss of $49,708. Also the trading of Martha Stewart’s shares occurred during the company’s blackout period which commenced on December 21st. At this time no shares from the company were permitted to occur and the stockbrokers at Merrill Lynch would have known that and should have advised their clients accordingly. It is our belief that prosecutors might consciously have had additional motives for pursuing the case. Martha Stewart a celebrity of high profile would sell newspapers if investigated and later indicted. A prosecutor who was able to make a strong, believable case would bring fame to himself/herself and possibly new job opportunities. 3. Do you agree with the jury that she was guilty beyond a reasonable doubt of the conspiracy and obstruction of justice charges? We agree with the jury that Martha Stewart was guilty beyond a reasonable doubt of the conspiracy and obstruction of justice charges. To establish a reasonable doubt of conspiracy, four main things must occur: a) Two or more persons in some way or manner, coming to a mutual understanding, in trying to accomplish a common and unlawful plan as charged in the indictment. An example of this includes the breakfast meeting between Martha Stewart and Peter Bacanovic on January 16th – after the sale of the shares – to construct a statement that they reproduced to the criminal authorities – that is, that Martha had agreed to sell her shares if the share price fell below $60.00 per share. Another example was illustrated when Douglas Faneuil was persuaded by his boss (Peter Bacanovic) to agree to the conspiracy constructed by his boss that there was a $60 stop-loss order on Martha Stewart’s ImClone shares. b) The person willfully became a member of such a conspiracy. Mr. Fanueil accepted a bribe from his boss (Peter Bacanovic) in the form of an extra week of vacation and a paid trip, so that he would not reveal the fact that Martha Stewart had been tipped off. Fanueil’s actions were acts of choice. c) That one of the conspirators during the existence of the conspiracy knowingly committed at least one of the methods (or overt act) described in the indictment. Bacanovic and Stewart repeatedly lied to the government agencies and attorneys in order to try to hamper the investigations. Bacanovic tampered the worksheet by adding â€Å"@60† near the entry for Stewart’s shares of Imclone. d) That such ‘overt act’ was a knowingly committed act done in order to carry out or accomplish some object of the conspiracy. Justification of this was seen when Bacanovic informed Faneuil that he must call Stewart to inform her of the Waksal’s actions. He decided to leave the message with Stewart’s administrative assistant in order for her to receive the message to allow her to carry out or give instructions on what actions to take. Faneuil had asked Bacanovic if he was allowed to tell Stewart and he stated â€Å"Of course that’s the whole point† On realizing what the written policy inside of the office stated he was very worried. Obstruction of justice is a crime. It is an offense that arises when someone tries to prevent, impede or influence the administration of justice, for example, bribing a juror, threatening a judge or encouraging false testimony. Obstruction of justice occurred when Stewart and Mr. Bacanovic conspired and continuously lied about the reason why Stewart sold her shares in an effort to hamper investigations. One such lie was the prearranged plan to sell Stewart’s shares if the price fell below $60 per share. 4. Was her punishment, including both imprisonment and fines appropriate? Were the punishment of Peter Bacanovic and Douglas Faneuil appropriate? We agree that the punishment imposed on Martha Stewart was a little too lenient. Due to her actions after being tipped off, she was able to make a profit of approximately $50,000, thus a fine of $30,000 still meant that she was gaining approximately $20,000. We believe that all of her profits should have been disgorged as compared to her wealth the amount is relatively small anyway. The imprisonment of five months imprisonment and then five months of home confinement, we believe was a suitable length of time. The relinquishing of her duties to act as an officer of a public company did not do her any damage as she still drew the same salary as she was accustomed to and even had a bonus. In her after-sentencing statement, she said that this had been no more than a personal matter that had been blown out of proportion; this in itself indicates that she was not remorseful about her actions. Whether these punishments were a deterrent for future action is questionable as Martha Stewart still violated the terms of her house arrest and this had to be subsequently extended for three weeks. We think that the punishments imposed on both Peter Bacanovic and Douglas Faneuil were inappropriate. First we look at Douglas Faneuil. Although he was following the instructions of his boss, he knew what he was told to do was wrong. He knew there was a displayed, written office policy with respect to client information privacy. He accepted a bribe from Mr. Bacanovic and waited approximately seven months after the incident before coming forward with the truth. A short term of imprisonment at a minimum security facility might have been added. With respect to Mr. Bacanovic, his penalties should have been harsher. His position at Merrill Lynch afforded him access to certain non-public information and as such his actions should have been within the law. He disregarded the policies of the company with respect to confidentiality, he also used his position to influence and bribe another employee of the company to comply with a conspiracy in the commitment of insider trading and he also conspired with his client Martha, to concoct an alibi to avoid prosecution by the government. He should have been given a heavier fine since he was the main person behind the scandal and had gained commission on the sale of both the Waksal and the Stewart shares. Also a longer term of imprisonment would have been fitting, maybe a term of two years.

Information and Geography of United Arab Emirates

Information and Geography of United Arab Emirates Population: 4,975,593 (July 2010 estimate)Capital: Abu DhabiBordering Countries: Oman and Saudi ArabiaArea: 32,278 square miles (83,600 sq km)Coastline: 819 miles (1,318 km)Highest Point: Jabal Yibir at 5,010 feet (1,527 m)United Arab Emirates is a country located on the eastern side of the Arabian Peninsula. It has coastlines along the Gulf of Oman and the Persian Gulf and it shares borders with Saudi Arabia and Oman. It is also located near the country of Qatar. United Arab Emirates (UAE) is a federation that was originally formed in 1971. The country is known as being one of the wealthiest and most developed in western Asia. Formation of United Arab Emirates According to the United States Department of State, UAE was originally formed by a group of organized sheikhdoms that lived on the Arabian Peninsula along the coasts of the Persian Gulf and the Gulf of Oman. These sheikdoms were known to have constantly been in dispute with one another and as a result, constant raids on ships the area was called the Pirate Coast by traders in the 17th and early 19th centuries.In 1820, a peace treaty was signed by the areas sheikhs in order to protect shipping interests along the coast. Raiding of ships continued until 1835 however, and in 1853 a treaty was signed between the sheikhs (Trucial Sheikhdoms) and the United Kingdom which established a perpetual maritime truce (US Department of State). In 1892 the U.K. and the Trucial Sheikhdoms signed another treaty that forged a closer relationship between Europe and the present-day UAE region. In the treaty, the Trucial Sheikhdoms agreed not to give away any of their land unless it went to the U.K. and i t established that the sheikhs would not begin new relationships with other foreign nations without first discussing it with the U.K. The U.K. then promised to provide military support to the sheikhdoms if needed.Throughout the mid 20th-century, there were several border disputes between the UAE and neighboring countries. In addition in 1968, the U.K. decided to end the treaty with the Trucial Sheikhdoms. As a result, the Trucial Sheikhdoms, along with Bahrain and Qatar (which were also being protected by the U.K.), tried to form a union. However they were unable to agree with each other so in the summer of 1971, Bahrain and Qatar became independent nations. On December 1 of the same year, the Trucial Sheikhdoms became independent when the treaty with the U.K. expired. On December 2, 1971, six of the former Trucial Sheikhdoms formed the United Arab Emirates. In 1972, Ras al-Khaimah became the seventh to join. Government of United Arab Emirates Today the UAE is considered a federation of seven emirates. The country has a federal president and prime minister which makes up its executive branch but each emirate also has a separate ruler (called an emir) who controls the local government. The UAEs legislative branch is made up of a unicameral Federal National Council and its judicial branch is made up of the Union Supreme Court. The seven emirates of the UAE are Abu Dhabi, Ajman, Al Fujayrah, Ash Shariqah, Dubai, Ras al-Khaimah and Umm al Qaywayn. Economics and Land Use in United Arab Emirates The UAE is considered one of the wealthiest nations in the world and it has a high per capita income. Its economy is based on oil but recently the government has begun programs to diversify its economy. Today the main industries of UAE are petroleum and petrochemicals, fishing, aluminum, cement, fertilizers, commercial ship repair, construction materials, boat building, handicrafts, and textiles. Agriculture is also important to the country and the main products produced are dates, various vegetables, watermelon, poultry, eggs, dairy products,  and fish. Tourism and the related services are also a large part of UAEs economy. Geography and Climate of United Arab Emirates United Arab Emirates is considered a part of the Middle East and it is located on the Arabian Peninsula. It has a varied topography and in its eastern portions but much of the rest of the country consists of flat lands, sand dunes,  and large desert areas. In the east there are mountains and UAEs highest point, Jabal Yibir at 5,010 feet (1,527 m), is located here.The climate of UAE is desert, although it is cooler in the eastern areas at higher elevations. As a desert, UAE is hot and dry year round. The countrys capital, Abu Dhabi, has an average January low temperature of 54ËšF (12.2ËšC) and an average August high temperature of 102Ëš (39ËšC). Dubai is slightly hotter in the summer with an average August high temperature of 106ËšF (41ËšC). More Facts About United Arab Emirates UAEs official language is Arabic but English, Hindi, Urdu,  and Bengali are also spoken 96% of the population of UAE are Muslim while a small percentage is Hindu or Christian UAEs literacy rate is 90% Sources: Central Intelligence Agency. CIA - The World Factbook - United Arab Emirates. Retrieved from: https://www.cia.gov/library/publications/the-world-factbook/geos/ae.htmlInfoplease.com. (n.d.). United Arab Emirates: History, Geography, Government, and Culture- Infoplease.com. Retrieved from: infoplease.com/ipa/A0108074.htmlUnited States Department of State. United Arab Emirates. Retrieved from: state.gov/r/pa/ei/bgn/5444.htmWikipedia.com. United Arab Emirates - Wikipedia, the Free Encyclopedia. Retrieved from: http://en.wikipedia.org/wiki/United_Arab_Emirates